Sony Ericsson VPL-PX30 User Manual

WORLDWORLDWORLDPROTOCOL MANUALMODEL...VPL-PX20VPL-PX30VPL-VW10HTLCD DATA/VIDEO PROJECTOR...DEST.VERSION 1.0Projector Firmware ARC32V

6VPL-PX20/PX30VPL-VW10HT5. Connection<RS-232C Connection>Communication is enabled by the use of a D-Sub 9 Pin cross (reverse) cable.The pin assi

7VPL-PX20/PX30VPL-VW10HT6. Communication Procedure6-1. Outline of CommunicationAll communication between CONTROLLER (PC, etc.) and DEVICE (PROJECTOR)

8VPL-PX20/PX30VPL-VW10HT7. Communication Rules. When sending a command from CONTROLLER, the return data (CMD1 = 10 hex or CMD1 = eachcategory value, C

9VPL-PX20/PX30VPL-VW10HT8. Approximate Return Waiting TimesNote: The times shown in this table are when communication is performed in the condition th

11VPL-PX20/PX30VPL-VW10HT119. CommandsFUNCTION CMD1 CMD2 DATA1 DATA2PX20/30 VW10DATA3 DATA4 DATA5 DATA6DATA7DATA8 DATA9 Power StatusACK EACH ACK 03h A

12VPL-PX20/PX30VPL-VW10HT12FUNCTION CMD1 CMD2 DATA1 DATA2PX20/30 VW10DATA3 DATA4 DATA5 DATA6DATA7DATA8 DATA9 Power Status00 FIXED 32 INPUT-A OO02 F

13VPL-PX20/PX30VPL-VW10HT13FUNCTION CMD1 CMD2 DATA1 DATA2PX20/30 VW10DATA3 DATA4 DATA5 DATA6DATA7DATA8 DATA9 Power Status00 FIXED 33 INPUT-B O 00 F

14VPL-PX20/PX30VPL-VW10HT14FUNCTION CMD1 CMD2 DATA1 DATA2PX20/30 VW10DATA3 DATA4 DATA5 DATA6DATA7DATA8 DATA9 Power StatusMEMORY 03h SET 00h RESET MEM

15VPL-PX20/PX30VPL-VW10HT1515Bit Categoryx0 x1 x2 x3 x4 x5 x6 x7 x8 x9 xA xB xC xD xE xF0x1x VOLUME VOLUME AUDIO POWER CONTRAST CONTRAST COLOR COLOR B

WARNING!!AN INSULATED TRANSFORMER SHOULD BE USED DURINGANY SERVICE TO AVOID POSSIBLE SHOCK HAZARD,BECAUSE OF LIVE CHASSIS.THE CHASSIS OF THIS RECEIVER

1VPL-PX20/PX30VPL-VW10HTTable of Contents1. Introduction ...12. Communication Spec

1VPL-PX20/PX30VPL-VW10HT1. IntroductionThis protocol manual describes the basic configuration and basic operations of various commands usedfor project

2VPL-PX20/PX30VPL-VW10HT2. Communication Specifications<RS-232C Communication Signal>. Full duplex communication channels (Flow control not perf

3VPL-PX20/PX30VPL-VW10HT3. Command Block FormatThe code from B0 to B (n) + 2 as described below are transmitted.1B0Start Code2 SENDER (To) Index9Bm

4VPL-PX20/PX30VPL-VW10HT4. Data of Code11111 Start Condition22222 INDEX Header/*-- RECEIVER INDEX --*//*-- SENDER INDEX --*//*-- Command --*/Note: CMD

5VPL-PX20/PX30VPL-VW10HT55555 Data Size 3Note: Error when 80 to FF hex codes are included.66666 DataBn = B16 + 1Bm = B16 + Total Data Length77777 Chec