CDP-XE570AEP ModelUK ModelSERVICE MANUALCOMPACT DISC PLAYERSony CorporationAudio Entertainment GroupGeneral Engineering Dept.9-873-878-112001C1600-1©
10CDP-XE570Procedure :1. Connect oscilloscpe to test point TP (TE1) and TP (VC) onBD BOARD.2. Turn Power switch on.3. Put disc (PATD-012) in to play t
11CDP-XE570[ BD BOARD ] – Side B –Adjustment Location :[ DISPLAY BOARD ] – Conductor side –CN102IC101TP(FE1)TP(TE1)TP(VC)TP(RF AC)TP2AFADJTP1ADJGNDS53
12CDP-XE570SECTION 6DIAGRAMS6-1. CIRCUIT BOARDS LOCATIONKEY boardDISPLAY boardHEADPHONE boardMAIN board BD boardLOADING boardPOWER SW board
1313CDP-XE570THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printedin each block.)For
1414CDP-XE5706-4. PRINTED WIRING BOARD BD SECTION • See page 12 for Circuit Board Location.There are a few cases that the part printed onthis
1515CDP-XE5706-5. SCHEMATIC DIAGRAM BD SECTION • See page 21,22 for IC Block Diagrams. • See page 13 for waveforms.IC B/DIC B/D
1616CDP-XE5706-6. PRINTED WIRING BOARD MAIN SECTION • See page 12 for Circuit Board Location.There are a few cases that the part printed onthis
1717CDP-XE5706-7. SCHEMATIC DIAGRAM MAIN SECTION • See page 22 for IC Block Diagram.IC B/D
1818CDP-XE5706-8. PRINTED WIRING BOARD DISPLAY SECTION • See page 12 for Circuit Board Location.There are a few cases that the part printed onth
1919CDP-XE5706-9. SCHEMATIC DIAGRAM DISPLAY SECTION • See page 20 for IC Pin Functions. • See page 13 for waveform.
2CDP-XE570The following caution label is located inside of the unit.This appliance is classifiedas a CLASS 1 LASERproduct.The CLASS 1 LASERPRODUCT MAR
2020CDP-XE5706-10. IC PINFUNCTIONS• AbbreviationFL : Fluorescent indicator tubePin No. Pin Name I/O Function41 VSS – Ground42 TX – Not used43 TEX – Co
21CDP-XE570IC101 CXD2587Q (BD BOARD)6-11. IC BLOCK DIAGRAMSTERFDCCEIGEN AVSS0 ADIO AVDD0CLTVFILOAVSS3VSSAVDD3DOUTVDDPCOFILIASYOASYIRFACBIASSSTPDFCTMI
22CDP-XE570IC131 CXA2518N-T4 (BD BOARD)IC631 BA6956AN (MAIN BOARD)1 2 3 4 5 6 7 8 9CONTROL LOGICTSDVREFOUT2OUT1RNFVMVCCFINGNDRINRW/ROMRW/ROMEQ ON/OF
SECTION 7EXPLODED VIEWSNOTE:• -XX, -X mean standardized parts, so they mayhave some differences from the original one.• Items marked “*” are not stock
24CDP-XE5707-2. CD MECHANISM SECTION (CDM66-5BD27)Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks101110110110111102113M151
25CDP-XE5707-3. BASE UNIT SECTION (BU-5BD27)151152153158154156160161M102M101#2157159155154not suppliedRef. No. Part No. Description Remarks Ref. No. P
NOTE:• Due to standardization, replacements in theparts list may be different from the partsspecified in the diagrams or the componentsused on the set
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks27CDP-XE570R153 1-216-864-11 METAL CHIP 0 5% 1/16WR155 1-216-836-11 METAL C
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks28CDP-XE570< SWITCH >S521 1-771-349-21 SWITCH, KEYBOARD(TIME/TEXT)S52
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks29CDP-XE570< JACK >J621 1-779-655-21 JACK (SMALL TYPE) (2 GANG)(CONTR
3CDP-XE570SECTION 1SERVICING NOTEHOW TO OPEN THE DISC TRAY WHEN POWER SWITCHTURNS OFFInsert a tapering driver into the aperture of the unit bottom, a
CDP-XE570REVISION HISTORYClicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised pag
4CDP-XE570Restrictions in CD-TEXT DisplayIn this unit, some special characters will not be displayed properly. These will be displayed as a space or a
5CDP-XE570! ” #$%&´ (21h to 27h)1kHz 0dB L&R( ) +,– . / (28h to 2Fh)01234567 (30h to 37h)8 9 : ; < = > ? (38h to 3Fh)@A B C D E F G (40h
6CDP-XE570SECTION 2GENERALFRONT PANELCHECK qf (12)CLEAR qg (12)Disc compartment 6 (8)Display qj (10)FADER 4 (13)PEAK SEARCH qd (14)PHONES jack ql (9)P
7CDP-XE570SECTION 3DISASSEMBLYNote : Follow the disassembly procedure in the numerical order given.3-1. LOADING PANEL• In order to remove the front p
8CDP-XE570SECTION 4TEST MODE4-1. CHECK MODEThe following checks can be performed in the CHECK Mode.• Offset value display1. Turn on the set.2. Put dis
9CDP-XE5704-3. ADJ MODEThe following operations are performed in the ADJ mode, which isset by connecting the TP1 (ADJ) terminal to the Ground and turn
Comments to this Manuals